Surface preparation.

The substrate to be painted must be dry, free from dust, grease stains and other contaminants. Heavily soiled surfaces should be cleaned with 3-5% baking soda solution, rinsed with water and dried and primed with Watergrunt deep penetration clearcole. Surfaces previously painted with oil paint or enamel must be cleaned of peeling coating, abraded to roughness and free of dust. Chalky whitewash should be completely removed. Irregularities, gouges and cracks should be leveled with acrylic filler. It is recommended to pre-treat the base to be painted with a penetrating water-dispersion acrylic primer TM Nanofarb, paint after 24 hours.

Application.

Stir Elastikfarbe Nanofarb thoroughly before use.

Preliminary preparation of slate, tiles:

Since the surfaces are quite porous, they need to be especially well cleaned before painting. This can be done in several ways: clean with an ordinary metal brush; use a special attachment for a drill or grinder; use a special washer that creates a high pressure jet. After cleaning, the surface must be dried and a thin coat of paint must be applied to bind the small particles and dust on the surface that remains. This will increase the adhesion of the paint to the surface. When the preparatory work is completed, you can proceed to painting the surface. The paint must be applied in 2-3 layers. The first layer is the main one. After painting the first layer, it is necessary to check for gaps, unpainted ends or corners. It is necessary to paint over carefully those places that are difficult to access. Apply the next layer only after the previous one has completely dried. The finishing layer will give uniformity to the coating, improve the protective and decorative effect.

Profiled sheeting, galvanized metal, aluminum

These surfaces must be thoroughly cleaned from rust, dirt, oil, grease and other contaminants and be degreased. Previously painted surfaces must be cleaned of old coatings. Remove rust mechanically. In cases of a large number of foci of corrosion, it is recommended to replace the affected sheets. Grease and oil stains are best cleaned with an alkaline solution, for example, a solution of washing powder. "White rust", which forms on the surface of galvanized metal or corrugated board, it is advisable to remove a solution of acetic acid and rinse thoroughly with detergents. Wash the cleaned surfaces thoroughly with clean water, preferably under pressure. Dry the surface well after rinsing. Painting of these materials does not require special equipment, so you must choose the most convenient method of applying paint.

Ferrous metal

The surface must be pre-cleaned from fragile coatings, dust, dirt, rust, scale, oil, grease and other contaminants, which should not remain even in the most inaccessible places. Before painting, ferrous metal must be primed with GF-021 anti-corrosion primer.

Mineral surfaces

Before applying paint, clean the surface from dust and treat it with Watergrunt deep penetration primer or Waterstop Nanofarb Concentrated Primer. The surface affected by moss, mold, fungi is recommended to be pre-cleaned and treated with an antiseptic for mineral surfaces.

Plywood, fiberboard, chipboard, particle board, wood

The surface must be clean and dry, thoroughly free from fragile coatings, dust, dirt, oil, grease and other contaminants. To destroy and prevent the appearance of fungus, mold, decay, treat the surface with an antiseptic for wooden surfaces.

Wallpapers

You can paint only after the wallpaper is completely dry. The minimum period that must pass from gluing the wallpaper to painting is 24 hours, the optimal interval is 2-3 days. For painting wallpaper, mainly a roller and a paint sprayer are used, for hard-to-reach places - a brush. The most even coverage is achieved with a paint sprayer. To avoid the formation of air bubbles, use sheepskin or velour rollers with medium pile.

Surfaces coated with alkyd or oil paints

Surfaces previously painted with oil or alkyd paints, polish to a matte state, rinse with a mild detergent solution, rinse thoroughly with water and dry.

Using Elastikfarbe Nanofarb (white).

Apply by roller, brush or spray (including airless) in two coats. For priming the base, it is recommended to dilute the paint with water no more than 10% by volume.

The drying time of the first layer is 2-3 hours at a temperature of +20 ° C and humidity not more than 50%.

Apply the second coat without diluting. Works should be carried out at ambient and substrate temperatures not lower than +5 ° C and not higher than +30 ° C.

Apply the second layer of paint 2-3 hours after applying the first one. Attention! The coating acquires its final color after the paint has dried. It acquires final resistance to wet cleaning in 3-4 weeks.

Colour: white

Note.

Ltd "NanoFarb" recommends performing works at a substrate temperature from +7 ° C to +27 ° C and relative humidity up to 70%. The manufacturer is not responsible for the end result if the recommendations were ignored.

Storage.

Store Elastikfarbe Nanofarb in its original packaging, with a seal on the container and in rooms with a constant temperature from +5 ° C to +30 ° C - 24 months from the production date indicated on the package. Do not expose to freezing and direct sunlight. Keep out of the reach of children.

Technical specifications.

• Density 1.4 kg / l
• Composition Water dispersion of styrene-acrylic resin with mineral fillers Substrate temperature during application from +7 ° C to +27 ° C
• Content of non-volatile substances (140 ° C).
• Not less than 65%
• PH level 8.0-8.5
• Consumption 1 kg up to 8 sq.m

Warranty.

The manufacturer guarantees that Elastikfarbe Nanofarb rubber paint compiles  with the specified technical characteristics if all the above rules are followed.

The manufacturer is not responsible for non-compliance with the above rules, as well as for non-compliance with the prescribed technical rules for the result of the work performed.

You can consult our phone manager on the use of Elastikfarbe Nanofarb. Also, a store employee will help you to place an order and introduce you to the delivery terms. You can buy Elastikfarbe Nanofarb in one click in our online store with delivery throughout Ukraine. Information about Elastikfarbe Nanofarb can be obtained on the website, as well as you can buy this product at the best price in Ukraine on the website.